Mosaic Mirror with Magnetic Flowers
A mosaic mirror with a magnetic surprise
Online since: 04/04/2008,
Number of visits: 382171
0
Laurie Glynn works as a mosaic artist and sent us these instructions for creating a small mosaic project with a magnetic surprise.
Required materials and tools:
- a piece of wood 30 x 30 cm, OSB board is best
- a round mirror tile, 20 cm in diameter
- a square mirror tile, 30 x 30 cm
- decorative magnets (The magnetic flowers used here are out of stock and will no longer be offered for sale.)
- counterpart magnets (S-08-03-N)
- approx. 200-250 g grout
- approx. 30 g pigment (optional)
- glass cutter
- tile pliers
- wheeled nipper
- glue (e.g. Weldbond and silicone)
1.
Position the round mirror tile in the middle of the wood and glue it on with silicone.
In my example, I surrounded the round mirror with a ball chain from the hardware store.
You could also use another type of bead chain, or simply leave this step out.
2.
Use silicone to glue the counterpart magnets (S-08-03-N) around the mirror, as many as you like, wherever you like.
But be careful! The magnets should not be placed too closely together, or they will collide uncontrollably (despite the glue).
Until the silicone has dried completely, make sure that nothing magnetic is placed near these magnets.
3.
Cut four pieces out of the square mirror tile to exactly fit the sides of the wood, then glue these pieces to the frame with silicone.
I filled the corners with a bit more of the ball chain but this is optional!
5.
Begin in any corner.
Spread a thin layer of glue (Weldbond or silicone) over a portion of the wood - small enough that you feel you can complete within about 5 minutes.
Place the outer edges first and ensure that the edge is as straight as possible.
I have laid the surface glass over the edge of the wood to meet the mirror pieces that were glued on earlier.
6.
Working piece by piece, lay out and glue the pieces that form the outer edge.
Afterwards you can use the remaining pieces of glass to fill the gap between the outer edge and the round mirror.
Where necessary cut smaller pieces of mirror to fit the spaces between larger pieces.
Try to lay the pieces so that the distance between each one is approximately the same and relatively small.
But make sure that there IS space between each piece! No piece of glass should touch its neighbor!
7.
When the surface is completely covered, let the mosaic dry for at least 24 hours.
The glue must be completely dry before beginning the grouting process.
8.
Mix approximately 200g.
grout with water in the ratio of 3:1, grout:water.
The mixture should be somewhat thick, like yoghurt.
Too much water makes grouting more difficult! You can color the grout with pigments if you choose.
Let the mixture stand untouched for 5 minutes.
9.
I use a kitchen spatula to spread the grout.
Spread the mixture with the side of the spatula, not with the end.
This requires less strength and is more effective as well! Remove excess grout on a regular basis, again using the side of the spatula.
Only then can you control the crevices to know if the grout has completely filled them.
The mirror will look pretty messy at this point but don't worry about it!
10.
When you have finished grouting, let your work sit for 30-60 minutes, depending on temperature.
Use a dry cloth to rub out the surface of the mosaic - if the grout smears rather than turning to dust, wait a bit longer.
11.
The decorative magnets can now be placed on their countermagnets, as desired.
Finished!
Further Examples
Here is an example with mosaic tiles (15 x 15 mm) rather than mirror tiles.
Small W-05-N
cubes were used as countermagnets for the decorative magnets.
Suitable decorative magnets
The entire content of this site is protected by copyright.
Copying the content or using it elsewhere is not permitted without explicit approval.
Copying the content or using it elsewhere is not permitted without explicit approval.